./_Man_SunOS_4.1.3_html/html4/ie.4s.html

Manual page for IE(4S)

ie - Intel 10 Mb/s Ethernet interface

CONFIG -- SUN-4 SYSTEM

device ie0 at obio ? csr 0xf6000000 priority 3
device ie1 at vme24d16 ? csr 0xe88000 priority 3 vector ieintr 0x75
device ie2 at vme24d16 ? csr 0x31ff02 priority 3 vector ieintr 0x76
device ie3 at vme24d16 ? csr 0x35ff02 priority 3 vector ieintr 0x77
device ie4 at vme24d16 ? csr 0x2dff02 priority 3 vector ieintr 0x7c

ie4 is supported on the SPARCsystems 300 and 400 only.

CONFIG -- SUN-3x SYSTEM

device ie0 at obio ? csr 0x65000000 priority 3
device ie1 at vme24d16 ? csr 0xe88000 priority 3 vector ieintr 0x75
device ie2 at vme24d32 ? csr 0x31ff02 priority 3 vector ieintr 0x76
device ie3 at vme24d32 ? csr 0x35ff02 priority 3 vector ieintr 0x77

CONFIG -- SUN-3 SYSTEM

device ie0 at obio ? csr 0xc0000 priority 3
device ie1 at vme24d16 ? csr 0xe88000 priority 3 vector ieintr 0x75
device ie2 at vme24d32 ? csr 0x31ff02 priority 3 vector ieintr 0x76
device ie3 at vme24d32 ? csr 0x35ff02 priority 3 vector ieintr 0x77

CONFIG -- SUN-3E SYSTEM

device ie0 at vme24d16 ? csr 0x31ff02 priority 3 vector ieintr 0x74

CONFIG -- SUN386i SYSTEM

device ie0 at obmem ? csr 0xD0000000 irq 21 priority 3

DESCRIPTION

The ie interface provides access to a 10 Mb/s Ethernet network through a controller using the Intel 82586 LAN Coprocessor chip. For a general description of network interfaces see if.4n

ie0 specifies a CPU-board-resident interface, except on a Sun-3E where ie0 is the Sun-3/E Ethernet expansion board. ie1 specifies a Multibus Intel Ethernet interface for use with a VME adapter. ie2 and ie3 specify SunNet Ethernet/VME Controllers, also known as a Sun-3/E Ethernet expansion boards.

DIAGNOSTICS

There are too many driver messages to list them all individually here. Some of the more common messages and their meanings follow.

ie%d: Ethernet jammed: Network activity has become so intense that sixteen successive transmission attempts failed, and the 82586 gave up on the current packet. Another possible cause of this message is a noise source somewhere in the network, such as a loose transceiver connection.
ie%d: no carrier: The 82586 has lost input to its carrier detect pin while trying to transmit a packet, causing the packet to be dropped. Possible causes include an open circuit somewhere in the network and noise on the carrier detect line from the transceiver.
ie%d: lost interrupt: resetting: The driver and 82586 chip have lost synchronization with each other. The driver recovers by resetting itself and the chip.
ie%d: iebark reset: The 82586 failed to complete a watchdog timeout command in the allotted time. The driver recovers by resetting itself and the chip.
ie%d: WARNING: requeuing: The driver has run out of resources while getting a packet ready to transmit. The packet is put back on the output queue for retransmission after more resources become available.
ie%d: panic: scb overwritten: The driver has discovered that memory that should remain unchanged after initialization has become corrupted. This error usually is a symptom of a bad 82586 chip.
ie%d: giant packet: Provided that all stations on the Ethernet are operating according to the Ethernet specification, this error ``should never happen,'' since the driver allocates its receive buffers to be large enough to hold packets of the largest permitted size. The most likely cause of this message is that some other station on the net is transmitting packets whose lengths exceed the maximum permitted for Ethernet.